Starting Red Fermentation
Grape Quantities Needed
Sometimes beginning winemakers have trouble estimating how many grapes are needed. The data shown in the Table provides a reasonable basis for making fruit estimates. For red wines, home winemakers often get about 150 gallons per ton using a small vertical basket press.
The values shown in the Table were calculated based on a yield of 150 gallons. Experienced winemakers always produce extra wine to use for topping up their storage containers.
Crushing breaks the skins of the berries and allows the juice to flow. Crushing should be done with a minimum of grinding and tearing of the grape tissues, and the seeds should never be broken. Small quantities of grapes can be crushed by hand, and several hundred pounds can be easily crushed by foot. Most home winemakers crush their grapes with a hand crank crusher. Both single and double roller crushers work well.
Stems contain much phenolic material. These phenolic compounds can contribute bitterness and astringency to wine, so most winemakers destem red grape varieties before starting fermentation. Stems can be removed quickly by "scrubbing" crushed gapes through a clean plastic milk crate.
Sulfur dioxide (SO2) helps winemakers control wild yeast and bacterial growth, and sulfur dioxide also helps reduce oxidation. Small wineries and home winemakers use potassium metabisulfite (sulfite) crystals to produce sulfur dioxide gas, and 25 to 50 milligrams per liter of sulfur dioxide are usually added to the crushed grapes before fermentation is started. A half teaspoon of crystals per 100 pounds of grapes is the correct amount. The sulfite powder should be dissolved in a small amount of water and stirred into the grapes.
Testing should be done when juice is available. Attempting to make a "big" red wine from immature fruit is hopeless, so winemakers prefer red grapes with a sugar content of at least 23 Brix. Consequently, sugar content is usually the first measurement made. Sugar can be measured with either a hydrometer or with a refractometer. Home winemakers are often advised to add sugar to immature fruit, but adding sugar will not increase the flavor or improve the weak varietal characteristics of immature grapes. Adding sugar to underripe grapes is seldom advisable, and normally, underripe red grapes are best used for making blush wines.
The titratable acid is also measured at crush time, and most
winemakers prefer to ferment red musts when the titratable
acidity (TA) falls between 0.6 and 0.75 percent. The TA can be measured using
an "acid test kit" or with a pipette, calibrated sodium hydroxide
and phenolphthalein solution. Grapes grown in
Yeast must have access to nitrogen, oxygen, vitamins, minerals, etc. to reproduce the large number of cells needed to complete fermentation, and grapes from under fertilized vineyards can be difficult to ferment to dryness unless extra nutrients are added. The manufacturer's directions should always be followed carefully when yeast nutrients are added because excessive quantities can produce off-odors.
Large differences exist in wine yeasts. The differences relate to speed of fermentation, color extraction, alcohol production, tendencies to stick, the quantity of foam generated, hydrogen sulfide production, etc. The type of yeast used for primary fermentation contributes little to the flavors of aged red wine.
Prise de Mousse is an excellent, general purpose yeast for both red and white wines. It produces little hydrogen sulfide, tolerates sulfur dioxide, tolerates high alcohol levels, and it seldom sticks.
Pasteur Red yeast is
becoming the yeast of choice for producing full-bodied "
Some home winemakers pour dry yeast into the juice. However, week fermentations often result, and better results are obtained when dry yeast is rehydrated. Use about a cup of warm water for 10 grams of dry yeast. The water temperature should be 100 F, so use a thermometer. Stir the water rapidly while the yeast is slowly added. Stir again after all the dry yeast has been added, and let the mixture stand for 20 or 30 minutes before adding the rehydrated yeast to the must.
Red grapes have colorless juice. The red color is in the skins. Red wines are made by fermenting the juice and the pulp, skins and seeds together. Astringency is a typical characteristic of red wine, and astringency comes from seeds, stems and skins. Most of the color is extracted in five or six days of skin contact time, but astringency and bitterness continue to be extracted from the seeds for weeks.
Small bubbles of carbon dioxide gas form during active fermentation. In red fermentations, the carbon dioxide bubbles adhere to the grape skins, and the bubbles make the skins more buoyant. As the bubbles collect, the skins float to the surface of the fermenting liquid, and after a few hours a thick layer of skins accumulates. Liquid slowly drains away as the layer of skins increases in thickness. This "cap" of skins becomes dry, and dry caps in open fermenters cause problems. Extraction becomes poor because most of the skins are out of the liquid, and vinegar bacteria can propagate rapidly in the cap. Fortunately, cap problems can be prevented easily by breaking up the cap periodically.
Caps on small fermentations are not very thick, and small caps can be managed by stirring the must with a large, wooden spoon two or three times each day. In larger fermentations, the cap becomes several inches thick, and a special tool is needed to push the cap back down into the juice. Most winemakers punch down the cap at least twice a day. Generally, more color and flavors can be extracted during the first few days of fermentation if the cap is gently punched down several times a day.
Red wines are normally fermented at temperatures ranging from 70 to 90 degrees, and within this temperature range, fermentations lasting from four to ten days are typical. Yeast cannot survive for long when fermentation temperatures exceed 90 degrees or so. Consequently, fermentations must be watched carefully, and cold water, ice or other means should be used to cool fermentation tanks when temperatures become excessive.
The speed of fermentation is determined primarily by the temperature. However, the type of yeast, the amount of initial sulfur dioxide added, nutrient levels, etc. also affect fermentation rates, so predicting when a fermentation will finish is difficult. Surprises can be avoided by measuring the temperature and the Brix at least once each day, and the fermentation should also be smelled and tasted.
Skin contact time is a standard method of controlling the astringency of red wines. Tannin content is low when short skin contact times are used, and soft, fruity red wines are produced. Fruity style red wines are often produced by pressing the fermentation when the sugar has dropped to eight or ten Brix. Full-bodied red wines are produced by five to ten days of skin contact (they are usually pressed when the hydrometer reads zero). Some "big" red wines are kept on the skins for three or four weeks, but very high quality grapes are needed for such extended maceration. Deciding when to press a red fermentation is part of the winemaking art.
Try to obtain cool
fruit, then crush, test, adjust and start fermentation promptly. Never crack
the seeds when crushing. Remove and discard most of the stems. Add a half
teaspoon of sulfite powder, mixed in an ounce or two of water, for each 100
pounds of grapes. Test the juice, and adjust the acid level of the must
before adding the yeast. Use active, dry Prise de